In U-Boot, we implemented the networked console via the standard "devices" mechanism, which means that you can switch between the serial and network input/output devices by adjusting the 'stdin' and 'stdout' environment variables. To switch to the networked console, set either of these variables to "nc". Input and output can be switched independently. We use an environment variable 'ncip' to set the IP address and the port of the destination. The format is :. If is omitted, the value of 6666 is used. If the env var doesn't exist, the broadcast address and port 6666 are used. If it is set to an IP address of 0 (or 0.0.0.0) then no messages are sent to the network. For example, if your server IP is 192.168.1.1, you could use: => setenv nc 'setenv stdout nc;setenv stdin nc' => setenv ncip 192.168.1.1 => saveenv => run nc On the host side, please use this script to access the console: +++++++++++++++++++++++++++++++++++++++++++ #! /bin/bash [ $# = 1 ] || { echo "Usage: $0 target_ip" >&2 ; exit 1 ; } TARGET_IP=$1 stty -icanon -echo intr ^T nc -u -l -p 6666 < /dev/null & nc -u ${TARGET_IP} 6666 stty icanon echo intr ^C +++++++++++++++++++++++++++++++++++++++++++ The script expects exactly one argument, which is interpreted as the target IP address (or host name, assuming DNS is working). The script can be interrupted by pressing ^T (CTRL-T). Be aware that in some distributives (Fedora Core 5 at least) usage of nc has been changed and -l and -p options are considered as mutually exclusive. If nc complains about options provided, you can just remove the -p option from the script. It turns out that 'netcat' cannot be used to listen to broadcast packets. We developed our own tool 'ncb' (see tools directory) that listens to broadcast packets on a given port and dumps them to the standard output. use it as follows: +++++++++++++++++++++++++++++++++++++++++++ #! /bin/bash [ $# = 1 ] || { echo "Usage: $0 target_ip" >&2 ; exit 1 ; } TARGET_IP=$1 stty icanon echo intr ^T ./ncb & nc -u ${TARGET_IP} 6666 stty icanon echo intr ^C kill 0 +++++++++++++++++++++++++++++++++++++++++++ Again, this script takes exactly one argument, which is interpreted as the target IP address (or host name, assuming DNS is working). The script can be interrupted by pressing ^T (CTRL-T). The 'ncb' tool can be found in the tools directory; it will not be built by default so you will ither have to adjust the Makefile or build it manually. For Linux, the network-based console needs special configuration. Minimally, the host IP address needs to be specified. This can be done either via the kernel command line, or by passing parameters while loading the netconsole.o module (when used in a loadable module configuration). Please refer to Documentation/networking/logging.txt file for the original Ingo Molnar's documentation on how to pass parameters to the loadable module. The format of the kernel command line parameter (for the static configuration) is as follows: netconsole=[src-port]@[src-ip]/[],[tgt-port]@/[tgt-macaddr] where src-port source for UDP packets (defaults to 6665) src-ip source IP to use (defaults to the interface's address) dev network interface (defaults to eth0) tgt-port port for logging agent (defaults to 6666) tgt-ip IP address for logging agent (this is the required parameter) tgt-macaddr ethernet MAC address for logging agent (defaults to broadcast) Examples: netconsole=4444@10.0.0.1/eth1,9353@10.0.0.2/12:34:56:78:9a:bc or netconsole=@/,@192.168.3.1/ Please note that for the Linux networked console to work, the ethernet interface has to be up by the time the netconsole driver is initialized. This means that in case of static kernel configuration, the respective Ethernet interface has to be brought up using the "IP Autoconfiguration" kernel feature, which is usually done by defaults in the ELDK-NFS-based environment. To browse the Linux network console output, use the 'netcat' tool invoked as follows: nc -u -l -p 6666 Note that unlike the U-Boot implementation the Linux netconsole is unidirectional, i. e. you have console output only in Linux.